Report
Question
Dom, I am replacing 2 circuit breakers with 2 arc fault breakers. I followed your youtube video and understand what I need to do to install 1st breaker. I disconnect neutral wire from neutral bar and connect to breaker. I then ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
in progress 0
Ron 7 years 1 Answer 256 views
0

Report
Question
I'm building a powder coat oven using using regular home stoves for my elements lights ect. I have a 220 welder in my garage(black-white-green wires) how do I connect the stove electronics wire(red-black-white-green wires) to my welder outlet? I've tried ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
solved 0
1 year 4 Answers 250 views
1

Report
Question
After a lot of rain in the Midwest, discovered the sump pump in basement causing water to seep in around the edges and carpet got wet. Is the carpet automatically toast? What would be a good replacement?

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
solved 0
2 years 1 Answer 237 views
1

Report
Question
My dryer stop heating up and came to realize the 30A 3prong outlet and 3prong dryer cord melted, so I removed outlet to replace and there is 4 wires rather then 3? Shouldn’t it had been a 4 prong outlet? ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
in progress 0
Samantha 1 year 1 Answer 237 views
0

Report
Question
Putting a sub panel in a workshop. Only going to use lights and recepticals, no welding or high amp tools. I have run 20amp wiring through out the shop. I have a dedicated line just for lights which there will ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
solved 0
2 years 8 Answers 235 views
0

Report
Question
Hi Dom, Just wanted to say I like your style and videos! I'll be adding additional outlets in my garage and will be using your technique :) Kurt

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
closed 0
1 year 1 Answer 234 views
1

Report
Question
I am adding electrical hot water heaters, 240 volt. Three heaters at 40 Amps each. And an electric car charger outlet, near future use. I suspect this will be too much for the current panel and am adding a sub ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. bk
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
in progress 0
1 year 3 Answers 234 views
0

Report
Question
Replacing my basement door. This store will be fastened to 2 x 6 which are embedded in the concrete wall. Can I install WRB To the 2x6 from and have it wrap outside to the concrete wall? My concern is ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Byron
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
in progress 0
1 year 4 Answers 232 views
0

Report
Question
I am putting a 50 amp panel in my garage. I ran 6/3 from the main panel in the house 50 feet to the 50 amp panel in the garage. My question is I only have 1 bus bar in ...

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
in progress 0
1 year 1 Answer 231 views
0

Report
Question
I am looking to add a few outlets in my basement, but the walls are covered in floor to ceiling blanket insulation. What is the best way to attach conduit and boxes to the wall.

Please briefly explain why you feel this question should be reported.

Report
Cancel
  1. Dominick Amorosso
    0
    Report

    Please briefly explain why you feel this answer should be reported.

    Report Cancel
    Attaching conduit to insulated basement walls
in progress 0
2 years 3 Answers 230 views
0